Copyright © 2000, Tjernlund Products, Inc. All rights reserved. P/N 8504090REV. 11/00RECOGNIZE THIS SYMBOL AS AN INDICATION OF IMPORTANT SAFETY INF
9IMPORTANT: CONFIRM PROPER IMPELLER ROTATION (VSAD-SERIES ONLY)All Auto-Draft® VSAD-Series Venters must use a Variable Frequency Drive (VFD) supplied
10FSAD-8/10 WIRED WITH A SINGLE GAS APPLIANCE AND NO VENTER POST-PURGEP/N 1303944 12/06/00ORANGEBLUEGREENREDYELLOWVSAD-8/10/12 WIRINGCOOLING FANMOTOR
11FSAD-12 WIRED WITH A SINGLE GAS APPLIANCE AND NO VENTER POST-PURGEFSAD-8/10 WIRED WITH A SINGLE GAS APPLIANCE AND 950-1067 1-10 MINUTE ADJUSTABLE PO
12FSAD-8/10 WIRED WITH A SINGLE OIL BURNER AND 950-1067 1-10 MINUTE ADJUSTABLE POST-PURGE RELAY/TIMERFSAD-12 WIRED WITH A SINGLE GAS APPLIANCE AND 950
13FSAD-12 WIRED WITH MULTIPLE GAS OR OIL APPLIANCES AND MAC-4 MULTIPLE APPLIANCE CONTROLFSAD-8/10 WIRED WITH MULTIPLE GAS OR OIL APPLIANCES AND MAC-4
14FSAD-12 WIRED WITH A SINGLE OIL BURNER AND 950-1067 1-10 MINUTE ADJUSTABLE POST-PURGE RELAY/TIMERVSAD-8/10/12 WIRED WITH A SINGLE GAS APPLIANCE AND
15VSAD-8/10/12 WIRED WITH MULTIPLE GAS OR OIL APPLIANCES AND MAC-4 MULTIPLE APPLIANCE CONTROLVSAD-8/10/12 WIRED WITH A SINGLE GAS APPLIANCE AND 950-10
PSA-1 FAN PROVER SAFETY INTERLOCK AND DRAFT ADJUSTMENT SET-UP PROCEDUREThe following Safety interlock procedure is only suitable when using a FSAD-Ser
5. Activate burner(s) at full capacity. Gradually adjust common manifold manual damper or VFD to maintain a slight negative draft (-0.02” W.C. or -5
The Tjernlund Auto-Draft® Venter is designed for continuous use. The motor is equipped with permanently lubricated sealed ballbearings which do not r
TABLE OF CONTENTSPAGE(S)AUTO-DRAFT® VENTER DESCRIPTION ...
Tjernlund Products, Inc. will issue credit to your Auto-Draft® provider or provide a free part to replace one that becomes defective dur-ing the two y
AUTO-DRAFT® VENTER FAN PERFORMANCE CURVESAuto-Draft® Venter performance was independently tested by an accredited AMCA certified testing facility.Sele
3INSTALLATION RESTRICTIONSFailure to install, maintain and/or operate the Auto-Draft® Venter in accordance with manufacturer's instructions may r
42. La température des gaz de combustion ne doit pas dépasser 575 °F (300 °C) au niveau de l'orifice d'admission du ventilateur de tirage Au
5TERMINATION CLEARANCES FOR U.S. INSTALLATIONSThe Auto-Draft® Venter base must be a minimum of 9” above a roof. Optional roof and wall mounting kits
6INSTALLATION OF THE AUTO-DRAFT® VENTER The Auto-Draft® Venter is designed to fit any type of nominal 8”, 10” or 12” diameter vent pipe. Vent pipe mu
75. Seal around the venter base and the Mounting Plate with hi-temp silicone. Make sure it is watertight and no water can slip in between the venter
88. Seal around the Venter base and the Mounting Plate with hi-temp silicone. Make sure it is watertight and no water can slip in between the Venter
Comments to this Manuals